here, its weird Ive been using the comp the whole time since Ive been home, since about 3:45 and it hasnt rebooted yet
| Attachments: |
|
info.jpg [ 117.13 KiB | Viewed 5546 times ] |
| n00bfest http://n00bfest.com/phpBB3/ |
|
| Installing new cpu http://n00bfest.com/phpBB3/viewtopic.php?f=11&t=30505 |
Page 1 of 2 |
| Author: | Spidey [ Thu Dec 03, 2009 3:25 pm ] |
| Post subject: | Installing new cpu |
All I will have to do is pull the old one out and put the new one in correct? Are will it require more? |
|
| Author: | fomenta [ Thu Dec 03, 2009 4:54 pm ] |
| Post subject: | Re: Installing new cpu |
Generally no, just make sure to clean off and add new thermal compound and plug the fan in :-) Never had to do this, but if it doesn't start up and the only thing you did was swap the CPU you should reset the CMOS (either with the jumper or by pulling the CMOS battery (if its removable) for a few minutes. |
|
| Author: | Spidey [ Thu Dec 03, 2009 5:00 pm ] |
| Post subject: | Re: Installing new cpu |
Ill have to try resetting bios it started up and said I needed to update my bios, then it powered down, and powers down everytime I power it up |
|
| Author: | Spidey [ Thu Dec 03, 2009 5:21 pm ] |
| Post subject: | Re: Installing new cpu |
flashing the bios seems to have done it for me. thank goodness for asus ez flash, makes it quick and painless |
|
| Author: | Spidey [ Fri Dec 04, 2009 4:08 pm ] |
| Post subject: | Re: Installing new cpu |
my comp reboots now and freezes up at the post screen then I reset it and it starts up fine, it saves a log but I cant seem to attach it here, this is some of it? IHM::Date = Thursday 03 December 2009 - 18:32 IHM::gOS = 0 IHM::gOS = 1 IHM::oMUTX = 0 IHM::oMUTX = 1 IHM::DisableIDE = 0 IHM::DisableLPCMonitoring = 0 IHM::DisableSPD = 0 IHM::DisableDMI = 0 IHM::DisableSMBus = 0 IHM::DisableSensor = 0 IHM::Disable16 = 0 IHM::DisableGPU = 0 IHM::CPUClockThread = 0 IHM::DisableACPI = 0 IHM::DisableNVSU = 0 IHM::gDX = 0 IHM::gDX = 1 IHM::gIE = 0 IHM::gIE = 1 Kernel::[bLockAccess] timeout=1000, wait = 0x0 IHM::gDMI = 0 IHM::gDMI = 1 IHM::rPCI = 0 Kernel::[bLockAccess] timeout=1000, wait = 0x0 IHM::rPCI = 1 Kernel::[bLockAccess] timeout=1000, wait = 0x0 IHM::iCPU = 0 IHM::iCPU = 1 IHM::giCPU = 0 IHM::giCPU = 1 IHM::gNB_MB = 0 IHM::gNB_MB = 1 IHM::giNB = 0 IHM::giNB = 1 IHM::giSB = 0 IHM::giSB = 1 IHM::gNB_GMCH = 0 IHM::gNB_GMCH = 1 IHM::giNB_GMCH = 0 IHM::giNB_GMCH = 1 Kernel::[bLockAccess] timeout=1000, wait = 0x0 IHM::gSMBus = 0 Kernel::nVidia SMBus #1 = 00005000 Kernel::nVidia SMBus #2 = 00005100 IHM::gSMBus = 1 IHM::gMULTIPLEX = 0 IHM::gMULTIPLEX = 1 IHM::gSENSOR = 0 IHM::gSENSORTYPE = 0 Kernel::ISA Scan 0 Kernel::00[3E] = FF Kernel::ISA Scan 1 Kernel::Sensor @ 90 IHM::gSENSORTYPE = 1 IHM::gNVSU = 0 Kernel::NVSU Port : 00000000 IHM::gNVSU = 1 IHM::gMCP = 0 IHM::gMCP = 1 IHM::gHECI = 0 IHM::gHECI = 1 IHM::gPCH_Thermal = 0 IHM::gPCH_Thermal = 1 IHM::gSENSOR = 1 IHM::gSMART = 1 IHM::gSMART = 1 Kernel::[bLockAccess] timeout=1000, wait = 0x0 IHM::gHDI_HWM = 0 IHM::gHDI_HWM = 1 IHM::gSPD = 0 IHM::gSPD = 1 IHM::gGPU = 0 IHM::gGPU = 1 Kernel::[bLockAccess] timeout=1000, wait = 0x0 IHM::giGPU = 0 Kernel::CurrentGPU 060510DE Kernel::IndexPCIGPU 28 Kernel::GPUDID 0605 Kernel::GPUVID 10DE Kernel::nVidia MMIO 0xD2000000 IHM::giGPU = 1 IHM::giNV = 0 Kernel::GPU 0 handle -1157623808 Kernel::GPU 0 handle -1157623808 IHM::giNV = 1 IHM::giEnumGPU = 0 IHM::giEnumGPU = 1 IHM::gPOW = 0 IHM::gPOW = 1 Kernel::[bLockAccess] timeout=1000, wait = 0x0 IHM::gLDT = 0 IHM::gLDT = 1 IHM::gPCI = 0 IHM::gPCI = 1 IHM::gIDE = 0 IHM::gIDE = 1 IHM::gACPI = 0 IHM::gACPI = 1 IHM::gSYS = 0 IHM::gSYS = 1 Kernel::[bLockAccess] timeout=1000, wait = 0x0 IHM::SUMMARY_START = 1 IHM::S_MB = 0 IHM::S_MB = 1 IHM::S_Chipset = 0 IHM::S_Chipset = 1 IHM::S_CPU #0 = 0 IHM::S_CPU #0 = 1 IHM::S_SPD = 0 IHM::S_SPD = 1 IHM::WinMem = 4096 IHM::S_GPU = 0 IHM::S_GPU = 1 IHM::BEGIN_DRIVE = 1 IHM::XP = 1 IHM::DiskDrive = 0 IHM::DiskDrive = 1 IHM::PnPEntity = 0 IHM::SCSIMediaType = 1 IHM::SCSIMediaType = 1 IHM::PnPEntity = 1 IHM::END_DRIVE = 1 IHM::S_EDID = 0 IHM::S_EDID = 1 IHM::S_EDID0 = 0 IHM::S_EDID0 = 1 IHM::S_EDID1 = 0 IHM::S_EDID1 = 1 IHM::S_NET = 0 IHM::S_NET = 1 IHM::SUMMARY_END = 1 Kernel::[bLockAccess] timeout=1000, wait = 0x0 Kernel::[bLockAccess] timeout=1000, wait = 0x0 Kernel::[bLockAccess] timeout=1000, wait = 0x0 |
|
| Author: | Genocide [ Fri Dec 04, 2009 4:09 pm ] |
| Post subject: | Re: Installing new cpu |
wheres the log? |
|
| Author: | Spidey [ Fri Dec 04, 2009 4:10 pm ] |
| Post subject: | Re: Installing new cpu |
there wouldnt let me attach it, theres is a whole lot of that kernal stuff, I played css on it all last night fine, this morning I woke up and it was froze up on that screen |
|
| Author: | the_yeti [ Fri Dec 04, 2009 4:17 pm ] |
| Post subject: | Re: Installing new cpu |
are you 100% sure your new cpu is 100% compatible with your mother board? it can be the same socket type, but an earlier mobo paired with a newer cpu, same socket and all, might not necessarily match well, especially if you're going from a dual core to a quad, for example. Just a thought. |
|
| Author: | Spidey [ Fri Dec 04, 2009 4:20 pm ] |
| Post subject: | Re: Installing new cpu |
The cpu is not posted on the asus site of supported cpus for the mb, but it meets all the requirements of my mb, and after reading this I feel that there should be no prob with my mb handling this. http://vip.asus.com/forum/view.aspx?id= ... uage=en-us this is my new cpu Intel Core 2 Duo E7600 Wolfdale 3.06GHz 3MB L2 Cache LGA 775 65W Dual-Core Processor |
|
| Author: | the_yeti [ Fri Dec 04, 2009 4:26 pm ] |
| Post subject: | Re: Installing new cpu |
hmmm... perhaps, check the bios settings and make sure this new bios you just flashed didn't default to some funky or otherwise undesirable settings... did you make sure you cleared the cmos after you flashed the bios? |
|
| Author: | Spidey [ Fri Dec 04, 2009 4:32 pm ] |
| Post subject: | Re: Installing new cpu |
no I didnt do that, I have pc wizard open right now and it shows my cpu voltage at 1.049V when in bios it is set to 1.4v, and set to stop running if it gets down to 1.25v. I could try to reset the cmos and see if that does it |
|
| Author: | Genocide [ Fri Dec 04, 2009 4:54 pm ] |
| Post subject: | Re: Installing new cpu |
what cpu and board give me as info as you can.... could be an issue with the multiplier or a slew of other settings. |
|
| Author: | Spidey [ Fri Dec 04, 2009 5:07 pm ] | ||
| Post subject: | Re: Installing new cpu | ||
here, its weird Ive been using the comp the whole time since Ive been home, since about 3:45 and it hasnt rebooted yet
|
|||
| Author: | Gman [ Fri Dec 04, 2009 6:07 pm ] |
| Post subject: | Re: Installing new cpu |
If you were using a single core before, and upgraded to a dual core, you might need to reinstall the correct HAL (hardware abstraction layer), which has to be done from the Windows Installation application (booting from the Windows CD). Not sure if you need to do that or not, but it's something you could try. |
|
| Author: | Spidey [ Fri Dec 04, 2009 6:15 pm ] |
| Post subject: | Re: Installing new cpu |
had a dual core b4 this one too |
|
| Author: | Spidey [ Fri Dec 04, 2009 7:55 pm ] |
| Post subject: | Re: Installing new cpu |
found this while googling. Could this maybe be it? My c1e is set to auto in bios I would imagine it's because the PC is trying to go into a sleep state and you've disabled speedstep/C1E in the BIOS? For example, if I mistakenly press 'sleep' in Vista, my PC restarts as it cannot sleep. Worth a punt |
|
| Author: | Spidey [ Fri Dec 04, 2009 9:03 pm ] | ||
| Post subject: | Re: Installing new cpu | ||
well after looking through my event logs there were a bunch of warning and a few critical errors. This was only happening when my comp was not being used and just idling. After booting from win7 disc and doing a repair it told me to remove and external devices and restart and see if prob persist. SO I unhooked my external hdd, went into bios boot options and for some reason the first boot option was removable, changed to hard disk and there are now no critical errors in the log. Just some warnings, I dont think this is anything major just trying to get me to change display setting to get better performance I believe. We shall see, I dont think this has anything to do with my cpu at all lawls. Gonna let the comp idle for a bit and see if it happens again
|
|||
| Author: | Spidey [ Sat Dec 05, 2009 8:17 am ] |
| Post subject: | Re: Installing new cpu |
well guess I was wrong, went to bed woke up the the BSOD, with this info Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7600.2.0.0.768.3 Locale ID: 1033 Additional information about the problem: BCCode: a BCP1: 0000000000000028 BCP2: 0000000000000002 BCP3: 0000000000000000 BCP4: FFFFF80002905090 OS Version: 6_1_7600 Service Pack: 0_0 Product: 768_1 Files that help describe the problem: C:\Windows\Minidump\120509-22167-01.dmp C:\Users\Parker\AppData\Local\Temp\WER-46004-0.sysdata.xml Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid= ... cid=0x0409 If the online privacy statement is not available, please read our privacy statement offline: C:\Windows\system32\en-US\erofflps.txt |
|
| Author: | r3xx3r [ Sat Dec 05, 2009 7:07 pm ] |
| Post subject: | Re: Installing new cpu |
Spidey wrote: well guess I was wrong, went to bed woke up the the BSOD, with this info Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7600.2.0.0.768.3 Locale ID: 1033 Additional information about the problem: BCCode: a BCP1: 0000000000000028 BCP2: 0000000000000002 BCP3: 0000000000000000 BCP4: FFFFF80002905090 OS Version: 6_1_7600 Service Pack: 0_0 Product: 768_1 Files that help describe the problem: C:\Windows\Minidump\120509-22167-01.dmp C:\Users\Parker\AppData\Local\Temp\WER-46004-0.sysdata.xml Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid= ... cid=0x0409 If the online privacy statement is not available, please read our privacy statement offline: C:\Windows\system32\en-US\erofflps.txt in the bsod there should have been a STOP message, that is what u need to put into google and it might come up with some help, that doesnt always work tho. get a .dmp reader, it will allow u to open the "C:\Windows\Minidump\120509-22167-01.dmp" file (i dont think u can do this w/o a .dmp reader). if u have trouble finding 1 let me know, i have used one, but dont remember it, but can find it. |
|
| Author: | Spidey [ Sat Dec 05, 2009 8:40 pm ] |
| Post subject: | Re: Installing new cpu |
damn I thought I included that, Ive been googling it and lots of diff things ppl say it could be. IRQL_NOT_LESS_OR_EQUAL |
|
| Page 1 of 2 | All times are UTC - 6 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|